Color steel plate characteristics and installation
Characteristics of color steel plate

color-coating http://www.camelsteel.com
A.) The color steel plates can be disassembled and then restored, which can be easily assembled and disassembled.
The standard unit wall panels can be interchanged, which is very convenient for the maintenance of water and electricity, and line transformation.
B) The color steel plate surface can be arbitrarily opened, which is very convenient for installing control switches,
power sockets and other devices, without additional processing.
C) The color of the surface of the color steel plate is soft, and it forms a unified and harmonious whole with the floor and ceiling, giving the whole space a modern atmosphere.
D) Using the electrostatic paint spraying process, the surface is smooth and delicate, does not accumulate dust,
and is easy to maintain, which greatly guarantees the cleanliness requirements of the machine room.
E) The color steel plate meets the national standard A-level fire protection standard,
which can fully meet the fire protection requirements for the construction and decoration of the computer room.
How to install
1) Color steel plate stakeout:
Stakeout carried out according to the drawing and on-site measured dimensions (the centerline of the partition wall),
and the centerline of the ground rail eject from the intersection of the centerline of the two edges and the ground.
Ensure that these four lines are in a vertical plane to ensure the verticality of the wall to be installed later.
2) Sky rail:
the installation should be neat, the joints should be reinforced and repaired, and the nails or screws should be fixed to the cement ceiling every 500mm-600mm.
3) Ground rail:
When installing the ground rail, the installation position of the door should be reserved first, and the problem of ground difference should be paid attention to.
If, the ground level difference is too large, it must level to reduce the level difference without affecting the level of adjustment.
Fix the floor with hits or screws every 600mm. If the ground seam is too large, fill it up with a caulking agent.
4) Edge finishing:
Cut edges according to the actual measurement value, and trim the edges after cutting.
Strive to be neat and consistent, and the joints must be seamless.
Pay special attention to the interface with the sky and skirting board, and make sure there is no gap.
5) Vertical keel:
set a vertical keel every 49cm (half the size of the partition).
The columns on both sides of the door frame completely fix up and down to prevent shaking.
A vertical keel adds in the opposite direction, and the width of the door leaf exceeds 90cm.
The horizontal column on the door frame must strengthen and fixed and fixed by welding if necessary.
6) Lateral piercing keel:
The height increase by more than 3 meters and one is set at 1.2 meters in the vertical direction.
When the two branches connect, they must overlap, and the overlapping length shall not be less than 10cm.
7) Wall panels:
Install color steel plates from one side, and install them in sequence, with 12mm spacing between the connected panels.
Use a 12mm width bead between partitions, and standard unit wall panels can be interchanged.
Precautions for installing
1) Adopt 12mm width bead between the boards, standard unit wallboards can interchange
2) Pay more attention to details when installing wall panels.
First, transport the wall panels to the vicinity of the installation point with a pallet truck, and then use the suction cups to erect the metal panels.
Make its lower end lean against the skirting board, and the two sides of the lining board are close to the vertical keel.
The distance between one side and the other wallboard is 12mm.
Use the fixing piece to lean on it, and then fix the self-tapping screw on the vertical keel.
The fixed spacing is between 300mm-400mm, and attention must be paid to the horizontal and vertical positions during assembly.
When it comes to the last wall panel, if you need to cut it, you must measure the size, then trim it in the correct way, and install it on the wall.
3) Use the “U”-shaped internal corner edge trimming strip to close the internal corner of the wall.
4) Custom-made color steel plates can use on the corners and pillars to achieve a beautiful and generous overall effect.
5) In order to keep the corners consistent with the wall, the corners of the wall adopt the same color professional edge.
3 comments. Leave new
Jeg har oppdaget store meldinger her. Jeg liker den metoden du forklare.
Hyggelig!
fantastic as well as amazing blog site. I really intend to thank you, for giving
us much better info.
You have a wonderful blog and also there is
a great deal of great info here!.